- Does OSPF use TCP or UDP?
- What port does OSPF use?
- IS IS routing protocol Cisco?
- Which of the following best describes OSPF?
- Why OSPF is called link state routing protocol?
- Which layer is OSPF?
- Does OSPF use hop count?
- Is Eigrp better than OSPF?
- IS IS protocol vs OSPF?
- What are the main differences between the OSPF and IS IS routing protocols?
- Is OSPF a routing protocol?
- What protocol does BGP use?
- Is OSPF Classful or classless?
- Is OSPF a layer 3 protocol?
- Which of the following is a routing protocol?
Does OSPF use TCP or UDP?
OSPF messages ride directly inside of IP packets as IP protocol number 89.
Because OSPF does not use UDP or TCP, the OSPF protocol is fairly elaborate and must reproduce many of the features of a transport protocol to move OSPF messages between routers..
What port does OSPF use?
RIP uses the User Datagram Protocol (UDP) as its transport protocol, and is assigned the reserved port number 520. Open Shortest Path First (OSPF) is a link-state routing protocol. OSPF does not use a TCP/IP transport protocol (UDP, TCP), but is encapsulated directly in IP datagrams with protocol number 89.
IS IS routing protocol Cisco?
IS-IS is an IGP, link-state routing protocol, similar to OSPF. It forms neighbor adjacencies, has areas, exchanges link-state packets, builds a link-state database and runs the Dijkstra SPF algorithm to find the best path to each destination, which is installed in the routing table.
Which of the following best describes OSPF?
Which of the following best describes OSPF? OSPF is a classless link-state routing protocol. … Network traffic due to sharing routing information is less than with the distance vector method. Convergence is faster than with the distance vector method.
Why OSPF is called link state routing protocol?
The OSPF protocol is a link-state routing protocol, which means that the routers exchange topology information with their nearest neighbors. The topology information is flooded throughout the AS, so that every router within the AS has a complete picture of the topology of the AS.
Which layer is OSPF?
data link layerOSI layer designation IS-IS runs on the data link layer (Layer 2) Open Shortest Path First (OSPF) is encapsulated in IP, but runs only on the IPv4 subnet, while the IPv6 version runs on the link using only link-local addressing. IGRP, and EIGRP are directly encapsulated in IP.
Does OSPF use hop count?
Distance-vector metrics RIP always uses the lowest hop count, regardless of the speed or reliability of a link. OSPF is a link-state protocol, which means that OSPF can take into account a variety of link conditions, such as the reliability or speed of the link, when determining the best path to a destination network.
Is Eigrp better than OSPF?
OSPF scales better than EIGRP because EIGRP is more complex in very large scale networks while troubleshooting. … OSPF have already been running in internal environments as an IGP (Interior Gateway Protocol). Thus, it is easier for an exchange of certain routes with OSFP.
IS IS protocol vs OSPF?
Comparison with OSPF. Both IS-IS and Open Shortest Path First (OSPF) are link-state protocols, and both use the same Dijkstra algorithm for computing the best path through the network. … While OSPF was natively built to route IP and is itself a Layer 3 protocol that runs on top of IP, IS-IS is an OSI Layer 2 protocol.
What are the main differences between the OSPF and IS IS routing protocols?
What are the main differences between the OSPF and IS-IS routing protocols? OSPF requires an area 0, while IS-IS does not. OSPF is a classful protocol, while IS-IS is a classless protocol. OSPF is a link state protocol, while IS-IS is not.
Is OSPF a routing protocol?
Open Shortest Path First (OSPF) is a routing protocol for Internet Protocol (IP) networks. It uses a link state routing (LSR) algorithm and falls into the group of interior gateway protocols (IGPs), operating within a single autonomous system (AS).
What protocol does BGP use?
TCPAmong routing protocols, BGP is unique in using TCP as its transport protocol. When BGP runs between two peers in the same autonomous system (AS), it is referred to as Internal BGP (i-BGP or Interior Border Gateway Protocol).
Is OSPF Classful or classless?
Classful routing protocols do not carry subnet masks; classless routing protocols do. Older routing protocols, including RIP and IGRP, are classful. Newer protocols, including RIP-2, EIGRP, and OSPF, are classless.
Is OSPF a layer 3 protocol?
At Layer 3, routers will use dynamic routing protocols (generally Open Shortest Path First or OSPF and BGP in most enterprises) to present a robust network that handles site-to-site link failures and minimizes the burden of IP management.
Which of the following is a routing protocol?
The key is to think of routing protocols as distance vector or link state protocols, IGP or EGP protocols, and classful or classless protocols. These are the overarching categories that common routing protocols like RIP, IGRP, OSPF, and BGP fall within.